Owner’s Manual
RC-1070
Stereo Control Amplifier
STEREO CONTROL AMPLIFIER RC-1070
VOLUME
RECORDING
OFF
LISTENING
CD AUX
CONTOUR
OFF
L-1
H
TUNER
CD
TUNER
TAPE
1
STAND BY
PHONES
L-2
LH
PHONO
AUX
PHONO
TAPE
2
TAPE
1
English
3
Cautions
WARNING: There are no user serviceable parts inside. Refer
all servicing to qualified service personnel.
WARNING: To reduce the risk of fire or electric shock, do not
expose the unit to moisture or water. Do not allow foreign
objects to get into the enclosure. If the unit is exposed to moisture,
or a foreign object gets into the enclosure, immediately dis-
connect the power cord from the wall. Take the unit to a qualified
service person for inspection and necessary repairs.
Read all the instructions before connecting or operating the component.
Keep this manual so you can refer to these safety instructions.
Heed all warnings and safety information in these instructions and on the
product itself. Follow all operating instructions.
Clean the enclosure only with a dry cloth or a vacuum cleaner.
You must allow 10 cm or 4 inches of unobstructed clearance around the
unit. Do not place the unit on a bed, sofa, rug, or similar surface that could
block the ventilation openings. If the unit is placed in a bookcase or cabi-
net, there must be ventilation of the cabinet to allow proper cooling.
Keep the component away from radiators, heat registers, stoves, or any
other appliance that produces heat.
The unit must be connected to a power supply only of the type and voltage
specified on the rear panel. (USA: 115 V/60Hz, EC: 230V/50Hz)
Connect the component to the power outlet only with the supplied power
supply cable or an exact equivalent. Do not modify the supplied cable. Do
not defeat grounding and/or polarization provisions. The cable should be
connected to a 2-pin polarized wall outlet, matching the wide blade of the
plug to the wide slot of the receptacle. Do not use extension cords.
Do not route the power cord where it will be crushed, pinched, bent, ex-
posed to heat, or damaged in any way. Pay particular attention to the power
cord at the plug and where it exits the back of the unit.
The power cord should be unplugged from the wall outlet if the unit is to be
left unused for a long period of time.
Immediately stop using the component and have it inspected and/or ser-
viced by a qualified service agency if:
• The power supply cord or plug has been damaged.
• Objects have fallen or liquid has been spilled into the unit.
• The unit has been exposed to rain.
• The unit shows signs of improper operation
• The unit has been dropped or damaged in any way
RC-1070 Stereo Control Amplifier
4
1: Controls and Connections
STEREO CONTROL AMPLIFIER RC-1070
VOLUME
RECORDING
OFF
LISTENING
CD AUX
CONTOUR
OFF
L-1
H
TUNER
TUNER
TAPE
1
CD
STAND BY
PHONES
L-2
LH
PHONO
AUX
PHONO
TAPE
2
TAPE
1
1
2
3
4
5
6
7
8
12V TRIGGER OUT
MODEL NO. RC-1070
PHONO
CD
TUNER
AUX
TAPE 1
TAPE 2
OUTPUTS
LEFT
LEFT
RIGHT
RIGHT
SWITCHED 400W MAX
IN
OUT
IN
OUT
1
2
SERIAL NO.
9
10
11
12
13
14 15
16
POWER
MUTE
A
B
D
E
1
4
7
0
2
5
8
3
6
9
VOLUME
TUNING
DISPLAY
+10
BAND
TP
F
PTY
TA
TUNE
PHONO
AUX 1
CD
TUNER
TAPE 1
/PRESET
C
AUX 2
PLAY
TAPE 2
STOP
G
PAUSE
RANDOM
RR-AT92
English
5
2: Output Connections
ROTEL RC-1070
12V TRIGGER OUT
MODEL NO. RC-1070
PHONO
CD
TUNER
AUX
TAPE 1
TAPE 2
OUTPUTS
LEFT
LEFT
RIGHT
RIGHT
SWITCHED 400W MAX
IN
OUT
IN
OUT
1
2
SERIAL NO.
AMPLIFIER
RIGHT INPUT
LEFT INPUT
RIGHT
LEFT
SPEAKERS
3: Input Connections
CD
PHONO
ROTEL RC-1070
12V TRIGGER OUT
MODEL NO. RC-1070
PHONO
CD
TUNER
AUX
TAPE 1
TAPE 2
OUTPUTS
LEFT
LEFT
RIGHT
RIGHT
SWITCHED 400W MAX
IN
OUT
IN
OUT
1
2
SERIAL NO.
TAPE
RC-1070 Stereo Control Amplifier
English
6
Contents
About Rotel
Getting Started
Thank you for purchasing the Rotel RC-1070
Stereo Control Amplifier. When used in a high-
quality audio system, it will provide years of
musical enjoyment.
Boxed numbers refer to RC-1070 illustration.
Boxed letters refer to RR-AT92 illustration.
A family whose passionate interest in music
led them to manufacture high fidelity compo-
nents of uncompromising quality founded Rotel
almost 40 years ago. Through the years that
passion has remained undiminished and the
family goal of providing exceptional value for
audiophiles and music lovers, regardless of
their budget, is shared by all Rotel employ-
ees.
Cautions ................................................3
The RC-1070 is a full featured, high perfor-
mance preamplifier. All aspects of the design
have been optimized to retain the full dynamic
range and subtle nuances of your music. The
RC-1070 has a highly regulated power sup-
ply incorporating a Rotel custom-designed
power transformer. This low impedance power
supply has ample power reserves, enabling
the RC-1070 to easily reproduce the most de-
manding audio signals. This type of design is
more expensive to manufacture, but it is bet-
ter for the music.
1: Controls and Connections
2: Output Connections
3: Input Connections
4
5
5
About Rotel ...........................................6
Getting Started ......................................6
Unpacking
Placement
Cables
The engineers work as a close team, listen-
ing to, and fine tuning each new product until
it reaches their exacting musical standards.
They choose components from around the
world in order to make that product the best
they can. You are likely to find capacitors from
the United Kingdom and Germany, semi con-
ductors from Japan or the United States, while
toroidal power transformers are manufactured
in Rotel’s own factory.
7
7
7
Remote Control ......................................7
Audio Controls
7
7
7
7
7
7
The RC-1070 printed circuit boards are de-
signed with Symmetrical Circuit Traces. This
insures that the precise timing of the music is
maintained and faithfully recreated. The
RC-1070 circuitry uses metal film resistors and
polystyrene or polypropylene capacitors in
important signal paths. All aspects of this de-
sign have been examined with the final goal
being faithful reproduction of music.
CD Functions
DVD Functions
Rotel’s reputation for excellence has been
earned through hundreds of good reviews and
awards from the most respected reviewers in
the industry, who listen to music every day.
Their comments keep the company true to its
goal – the pursuit of equipment that is musi-
cal, reliable and affordable.
Tuner Functions
Remote Sensor
Remote Control Batteries
Signal Connections..................................8
Outputs
8
8
8
The RC-1070 is straightforward in its installa-
tion and operation. If you have experience with
other stereo systems, you shouldn’t find any-
thing perplexing. Simply plug in the associ-
ated components and enjoy.
Line Level Inputs
Recorder Connections
All of us at Rotel thank you for buying this
product and hope it will bring you many hours
of enjoyment.
Phono Inputs
Ground Terminal
8
AC Power and Control ............................8
Please read this manual carefully. It provides
complete information on how to incorporate
the RC-1070 into your system as well as gen-
eral information that will help you get optimum
performance. Please contact your authorized
Rotel dealer for answers to any questions. In
addition, all of us at Rotel welcome your ques-
tions and comments.
AC Power Input
8
POWER/STANDBY Switch
Power Indicator
8
Auxiliary Power Outlets
(North American version)
8
8
12V TRIGGER Connection
Audio Controls .......................................9
VOLUME Control
CONTOUR Selector
LISTENING Selector
RECORDING Selector
MUTE Button
9
9
9
9
9
9
PHONES Output
Specifications .........................................9
English
7
Unpacking
Remote Sensor
Remote Control
The RC-1070 includes an RR-AT92 remote con-
trol that operates many of the controls of the
RC-1070. In addition, the remote operates
basic features of some Rotel CD players, DVD
players, and AM/FM tuners.
Carefully remove the RC-1070, the remote
control, and accessories from the shipping
carton. Save the shipping carton and all en-
closed packing material for future use. Ship-
ping or moving the unit in anything other than
the original packing material may result in se-
vere damage.
The remote sensor receives infrared signals
from the remote control. Do not cover or block
the sensor. It must be unobstructed or the re-
mote control will not work properly.
The operation of the Remote Sensor can also
be affected if it is exposed to bright sunlight
or certain types of lighting (such as halogen
lights) that emit infrared light. In addition re-
mote control functions may not work reliably
if the batteries in the RR-AT92 are weak.
Audio Controls
Keep the original sales receipt. It is your best
record of the date of purchase, which you will
need in the event warranty service is ever
required.
The RR-AT92 duplicates the basic audio func-
tions of the RC-1070 front panel. When a
function is available on both the front panel
and the remote, a number (front panel con-
trols) and a letter (remote buttons) are shown
in the instructions. For example, to change the
volume level you can either turn the control
on the front panel or use the buttons
NOTE: To use the remote, aim it at the remote
sensor on the front panel of the RC-1070.
Placement
Like all audio components that handle low-level
signals, the RC-1070 can be affected by its
environment. To minimize the chance the
RC-1070 will pick up hum or interference, do
not place it on top of an amplifier or any other
device with a large power transformer. Keep
the RC-1070 away from devices that have mo-
tors for the same reason. Do not place the
RC-1070 where it will be exposed to direct
sunlight.
Remote Control Batteries
Two UM-4/AAA size batteries (supplied) must
be installed before the remote control can be
used. To install the batteries, remove the cover
on the back of the RR-AT92. Install the batter-
ies as shown in the illustration in the battery
well. Test the control for proper operation, then
replace the cover. When the batteries become
weak the remote control won’t operate the
RC-1070 consistently. Installing fresh batter-
ies should eliminate the problem.
on the remote control. When only one identi-
fier appears, that control is available only on
the front panel or the remote, but not both.
CD Functions
The PLAY, STOP, PAUSE, TRACK +/–, RAN-
DOM buttons, and NUMERIC keys (0-10)
operate many Rotel CD players after the CD
button on the remote has been pressed.
We recommend installing the RC-1070 in fur-
niture designed to house audio components.
Such furniture is designed to reduce or sup-
press vibration which can adversely affect
sound quality. Ask your authorized Rotel dealer
for advice about component furniture and
proper installation of audio components.
NOTE: Remove the batteries from the remote
if it will not be used for a long period of time.
Do not leave run down batteries in the re-
mote control; they can leak corrosive chemi-
cals which will damage the unit.
DVD Functions
The PLAY, STOP, PAUSE, and TRACK +/–,
buttons operate Rotel DVD players, after the
AUX1 button on the remote has been pressed.
The RC-1070 is supplied with an RR-AT92
remote control and must be placed where the
infrared signal from the remote can reach the
front panel Remote Sensor.
Tuner Functions
The BAND, TUNING, and additional tuning
feature buttons operate Rotel tuners, after the
TUNER button on the remote has been pressed.
Cables
By default, the RR-AT92 operates the Rotel
RT-955 tuner. Alternatively, the remote can be
reprogrammed to operate the RT-940AX tuner.
This programming only needs to be done once:
Keep power cords, digital cables, and audio
cables away from each other. This will mini-
mize the chance of the audio signal cables
picking up noise or interference from the power
cords or digital cables. Using high quality,
shielded cables will also help to prevent noise
or interference. If you have any questions see
your authorized Rotel dealer for advice about
the best cable to use with your system.
To program for the RT-940AX: press the
POWER button and the 2 button simultaneously.
To program for the RT-955: press the
POWER button and the 1 button simultaneously.
RC-1070 Stereo Control Amplifier
8
When connecting a recorder to the RC-1070,
the outputsof the recorder must be connected
to the tape inputs of the RC-1070. Similarly
the tape outputsof the RC-1070 must be con-
nected to the inputs of the recorder. Be sure
to connect the Left and Right channels of each
device to the proper channels on the associ-
ated components. Use high quality connect-
ing cables to prevent loss of sound quality.
If you are going to be away from home for
an extended period of time such as a month-
long vacation, it is a sensible precaution to
unplug your audio and video components while
you are away.
Signal Connections
The RC-1070 has inputs for line level and phono
source components, connections for audio tape
decks, and output connections to send signals
to power amplifiers.
POWER/STANDBY Switch
Power Indicator
NOTE: To prevent loud, potentially damaging,
noises, make sure the system is turned off
when you make any signal connections.
The Power Indicator light above the STANDBY
button is always illuminated when the RC-1070
is connected to a live AC outlet. When the
front panel STANDBY button or remote con-
trol POWER button is pressed, the RC-1070
is turned on. The LISTENING control indica-
tor lights and VOLUME CONTROL indicator
light will illuminate. Pressing either button again
will put the RC-1070 in standby mode and these
indicator lights are turned off.
NOTE: The tape inputs can also be used for
standard playback-only source components,
omitting the output connections.
Outputs
See Figure 2
Phono Inputs
Ground Terminal
The RC-1070 has RCA-type output connectors
that are compatible with the inputs of most
power amplifiers. Use high quality cables and
be sure to connect the Left and Right channel
outputs of the RC-1070 to the correct chan-
nels of the amplifier.
The RC-1070 has a built-in phono preampli-
fier. To connect a turntable, connect the Left
and Right RCA signal cables to the Left and
Right RCA inputs labeled PHONO. Be sure
to connect the Left and Right channels to the
proper channels. Attach the ground wire from
the turntable to the Ground screw-terminal on
the back panel.
Auxiliary Power Outlets
(North American version)
There are two sets of variable gain outputs on
the RC-1070. The second set of outputs may
be used in custom system configurations to drive
a second power amplifier or to supply a sig-
nal to a signal processor.
The RC-1070 has two switched outlets on the
back panel. Power is available from these
outlets when the RC-1070 is turned on. These
outlets can provide up to a total of 400 watts.
They are appropriate for supplying power to
signal sources, such as CD players, tuners, or
tape decks. They should not be used for power
amplifiers. Connecting components that will
draw more than 400 watts to these outputs
could damage the RC-1070.
AC Power and Control
Line Level Inputs
See Figure 3
AC Power Input
The RC-1070 has three pair of conventional
RCA input connectors for line level components
such as CD players, video cassette recorders,
tuners, Laser Disc players, or DVD players.
These inputs are labeled CD, TUNER, and AUX.
The RC-1070 does not use a significant amount
of power. However there are two auxiliary
power outlets on the back panel, which can
be used to supply power for other units. Con-
sequently, it is best to plug the RC-1070 di-
rectly into a 2-pin polarized wall outlet. Avoid
the use of extension cords. A heavy duty power
outlet strip may be used if it (and the wall out-
let) is rated to handle the current demanded
by the components connected to it.
NOTE: Do not connect a power amplifier to
the auxiliary power outlets on the RC-1070.
Power amplifiers often draw more power than
these outlets can provide.
The Left and Right channels are clearly labeled
and should be connected to the correspond-
ing channels of the source component. The
Left RCA connectors are white, the Right con-
nectors are red. Use high quality RCA cables
for connecting input source components to the
RC-1070. Ask your authorized Rotel dealer
for advice about cables.
12V TRIGGER Connection
Several Rotel amplifiers can be turned on and
off using a 12 volt trigger signal. This connection
provides this 12 volt trigger signal. When the
RC-1070 is activated, a 12 volt DC signal
appears at this connector and will turn on an
amplifier. When the RC-1070 is put in
STANDBY mode, the trigger signal is interrupted
and the amplifier will be turned off.
Your RC-1070 is configured at the factory for
the proper AC line voltage in the country where
you purchased it (USA: 115 volts/60Hz AC
or CE: 230 volts /50 Hz AC ). The AC line
configuration is noted on a decal on the back
panel. Plug the supplied cord into the AC INPUT
receptacle on the back of the unit.
Recorder Connections
See Figure 3
Tape inputs and outputs can be connected to
any record/playback device that accepts stan-
dard line level analog input and output sig-
nals. Typically that will be a conventional tape
recorder. There are two sets of tape connec-
tions on the back panel, labelled TAPE 1 and
TAPE 2.
NOTE: Should you move your RC-1070 am-
plifier to another country, it is possible to
reconfigure your amplifier for use on a differ-
ent line voltage. Do not attempt to perform
this conversion yourself. Opening the enclo-
sure of the RC-1070 exposes you to danger-
ous voltages. Consult a qualified service
person or the Rotel factory service department
for information.
English
9
RECORDING Selector
Audio Controls
Specifications
The RC-1070 can record from any input source
(except TAPE 2) to a recorder connected to
TAPE 1 or TAPE 2 outputs. To select an input
source for recording, turn the RECORDING
control on the front-panel to the desired source.
Total Harmonic Distortion (20 Hz-20 kHz)
The following controls are used to operate the
RC-1070.
< 0.006%
Intermodulation Distortion
< 0.006% at 1V output (60 Hz:7 kHz, 4:1)
VOLUME Control
Input Sensitivity/Impedance
Line Level: 150 mV/24 kOhms
Phono (MM): 1.2mV/68k ohms
Turn the front panel VOLUME control clock-
wise to increase the volume, or counterclock-
wise to decrease the volume. Alternatively, press
the VOL buttons on the remote control to ad-
just the volume up or down
This selection is independent of the source
selected for listening. While recording, you
may still select a different source using the
LISTENING selector.
Output Level/Impedance
1V/100 Ohms
Usable Headphone Impedance
8 – 2,000 Ohms
If you have a three-head recorder or a DAT
recorder that allows simultaneous read and
write operation, you can monitor your recording
by setting the LISTENING switch to the TAPE
1 or TAPE 2 position.
Frequency Response
Line Level: 4Hz – 100kHz, +0, -3dB
Phono: 20Hz – 20kHz, 0.5dB
CONTOUR Selector
Instead of conventional tone controls, the
RC-1070 has a front-panel CONTOUR con-
trol which selects one of five available settings.
Each setting provides a fixed frequency con-
tour as follows:
Signal to Noise Ratio (IHF “A” weighted)
Line Level: 95 dB
Phono: 70 dB
NOTE: If you select TAPE 1 with the RECORD-
ING control, the recording signal will only
be available at the TAPE 2 recording outputs,
not the TAPE 1 outputs. To dub a tape, select
TAPE 1 and record to the tape deck connected
to the TAPE 2 outputs.
Phono Overload:
70mV
Power Requirements
USA: 115 Volts, 60 Hz
CE: 230 Volt, 50 Hz
OFF: the tone contour circuits are bypassed
to ensure the purest possible sound.
Power Consumption
10 Watts
L-1: moderate increase in bass frequencies
(typically +3dB @ 100Hz).
Dimensions (W x H x D)
430 x 92 x 344 mm
17” x 35/8” x 135/8”
MUTE Button
L-2: more increase in bass frequencies (typi-
cally +4dB @ 100Hz).
To temporarily mute the sound of the system
press the MUTE button on the RR-AT92 remote.
Press the button again to return the sound
volume to the original level. The LED in the
volume control will flash when the unit is muted.
Weight (net)
5.4 kg, 11.9 lbs.
H: moderate increase in high frequencies
(+3dB @ 10kHz).
All specifications are accurate at the time of
printing.
LH: combination of L-2 bass and H high fre-
quency increases.
Rotel reserves the right to make improvements
without notice.
PHONES Output
Rotel and the Rotel HiFi logo are registered
trademarks of The Rotel Co, Ltd., Tokyo, Japan.
LISTENING Selector
The PHONES output allows you to connect
headphones for private listening. This output
accepts standard stereo phone (1/4”) plugs.
If your headphones have another type of plug,
such as a 1/8” mini-plug, you will need an
adapter plug. Contact your authorized Rotel
dealer, to get the correct adapter plug.
The setting of the LISTENING selector controls
which of the input signals goes to the main
outputs and onto the power amplifier – or, more
simply, which source is heard. Turn the front
panel control to the source you want to hear,
or press the corresponding button on the
RR-AT92 remote.
NOTE: Plugging in headphones does not cut
off the signal to the outputs. In most instances,
you should turn off the power amplifier when
listening to headphones.
NOTE: The AUX1 button on the remote dupli-
cates the function of the front panel AUX but-
ton.
The Rotel Co. Ltd.
10-10 Shinsen-Cho
Shibuya-Ku
Tokyo 150-0045
Japan
Phone: +81 3-5458-5325
Fax: +81 3-5458-5310
Rotel of America
54 Concord Street
North Reading, MA 01864-2699
USA
Phone: +1 978-664-3820
Fax: +1 978-664-4109
Rotel Europe
Meadow Road
Worthing, West Sussex BN11 2RX
England
Phone: +44 (0)1903 524 813
Fax: +44 (0)1903 524 831
Rotel Deutschland
Kleine Heide 12
D-33790 Halle/Westf.
Germany
Phone: +49 05201-87170
Fax: +49 05201-73370
www.rotel.com
082 OM-RC-1070 English 090500
|