Owner’s Manual
Thank you, and congratulations on your choice of the Roland CUBE-60 Guitar Amplifier.
These sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature
provided by your new unit, Owner’s manual should be read in its entirety. The manual
should be saved and kept on hand as a convenient reference.
Before using this unit, carefully read the sections entitled
• IMPORTANT SAFETY INSTRUCTIONS (p. 2)
• USING THE UNIT SAFELY (p. 3–p. 4)
• IMPORTANT NOTES (p. 5).
This unit is equipped with a protection circuit.
The protection circuit helps ensure safety by operating when excessive input continues for
a long time while the device is at a location with a high ambient temperature. Sound drop-
out may occur when the protection circuit is actuated during use.
Please read through the documentation carefully to ensure correct use.
Main Features
• 60-watt output, high-performance, DSP guitar amp with built-in 30 cm (12-inch) speaker.
• Offers nine types of COSM amps, including realistic modeling of seven of the most
popular guitar amps and two original amp types, “ACOUSTIC” and “DYNA AMP.”
The newly developed “DYNA AMP” lets you achieve previously unexperienced levels
of tonal variation based on your picking dynamics, for whole new levels of expression.
Composite Object Sound Modeling (COSM) is Roland’s innovative and powerful
sound modeling technology. COSM analyzes the many factors that make up the
original sound, such as the electrical and physical characteristics of the original, and
then produces a digital model that can reproduce the same sound.
• Channel can be switched between “JC CLEAN” and “LEAD.” Channel switching can
be done via foot switch (optional).
• In addition to an easy-to-use, 3-band equalizer, the CUBE-60 also features a PRESENCE
knob, which you can use to create a wide variety of precisely defined sounds.
• Comes equipped with four effects types, chorus, flanger, phaser, and tremolo, along
with an independent system with the basic delay and reverb effects. You can also use
foot switches (optional) to switch these effects on and off.
• Equipped with a convenient “RECORDING OUT jack” handy for use in recording.
This output also functions as a headphone jack.
Also features LINE OUT, TUNER OUT, and EXT SPEAKER outs. These outputs can be
used for all kinds of performances, from recording to live gigs.
Copyright © 2004 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
USING THE UNIT SAFELY
The
symbol alerts the user to important instructions
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
•
001 Before using this unit, make sure to read the
•
010 This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could
cause permanent hearing loss. Do not operate for
a long period of time at a high volume level, or at
a level that is uncomfortable. If you experience
any hearing loss or ringing in the ears, you should
immediately stop using the unit, and consult an
audiologist.
instructions below, and the Owner’s Manual.
..........................................................................................................
002a
•
Do not open or perform any internal modifica-
tions on the unit.
..........................................................................................................
•
003 Do not attempt to repair the unit, or replace parts
..........................................................................................................
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
•
011 Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
distributor, as listed on the “Information” page.
..........................................................................................................
004 Never use or store the unit in places that are:
..........................................................................................................
•
012a:
•
Immediately turn the power off, remove the
power cord from the outlet, and request servicing
by your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page when:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or are
• Damp (e.g., baths, washrooms, on wet floors); or are
• Humid; or are
• The power-supply cord, or the plug has been
damaged; or
• Exposed to rain; or are
• Dusty; or are
• If smoke or unusual odor occurs
• Subject to high levels of vibration.
..........................................................................................................
• Objects have fallen into, or liquid has been
spilled onto the unit; or
•
007 Make sure you always have the unit placed so it is
• The unit has been exposed to rain (or otherwise
has become wet); or
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
..........................................................................................................
• The unit does not appear to operate normally or
exhibits a marked change in performance.
..........................................................................................................
013 In households with small children, an adult
008a
•
The unit should be connected to a power supply
only of the type described in the operating instruc-
tions, or as marked on the rear side of unit.
•
..........................................................................................................
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
•
009 Do not excessively twist or bend the power cord,
nor place heavy objects on it. Doing so can
damage the cord, producing severed elements and
short circuits. Damaged cords are fire and shock
hazards!
..........................................................................................................
014 Protect the unit from strong impact.
•
(Do not drop it!)
..........................................................................................................
..........................................................................................................
3
103a:
•
•
015 Do not force the unit’s power-supply cord to share
At regular intervals, you should unplug the power
an outlet with an unreasonable number of other
devices. Be especially careful when using
plug and clean it by using a dry cloth to wipe all
dust and other accumulations away from its prongs.
Also, disconnect the power plug from the power
outlet whenever the unit is to remain unused for an
extended period of time. Any accumulation of dust
between the power plug and the power outlet can
result in poor insulation and lead to fire.
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
..........................................................................................................
104 Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
106 Never climb on top of, nor place heavy objects on
..........................................................................................................
016 Before using the unit in a foreign country, consult
•
•
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
•
..........................................................................................................
026 Do not put anything that contains water (e.g.,
flower vases) on this unit. Also, avoid the use of
insecticides, perfumes, alcohol, nail polish, spray
cans, etc., near the unit. Swiftly wipe away any
liquid that spills on the unit using a dry, soft cloth.
..........................................................................................................
the unit.
•
..........................................................................................................
107a
•
Never handle the power cord or its plug with wet
hands when plugging into, or unplugging from,
an outlet.
..........................................................................................................
108a
•
Before moving the unit, disconnect the power
plug from the outlet, and pull out all cords from
external devices.
101a
•
The unit should be located so that its location or
position does not interfere with its proper venti-
lation.
..........................................................................................................
109a
•
Before cleaning the unit, turn off the power and
unplug the power cord from the outlet (P. 5).
..........................................................................................................
102a
•
Always grasp only the plug on the power-supply
cord when plugging into, or unplugging from an
outlet.
..........................................................................................................
110a
•
Whenever you suspect the possibility of lightning
in your area, pull the plug on the power cord out
of the outlet.
..........................................................................................................
..........................................................................................................
For EU Countries
This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
4
IMPORTANT NOTES
291b
In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2,
3 and 4, please read and observe the following:
Power Supply
Maintenance
301
401a
• Do not connect this unit to same electrical outlet that is being
• For everyday cleaning wipe the unit with a soft, dry cloth
used by an electrical appliance that is controlled by an
inverter (such as a refrigerator, washing machine,
or one that has been slightly dampened with water. To
remove stubborn dirt, use a cloth impregnated with a
mild, non-abrasive detergent. Afterwards, be sure to wipe
the unit thoroughly with a soft, dry cloth.
microwave oven, or air conditioner), or that contains a
motor. Depending on the way in which the electrical
appliance is used, power supply noise may cause this unit to
malfunction or may produce audible noise. If it is not
practical to use a separate electrical outlet, connect a power
supply noise filter between this unit and the electrical outlet.
402
• Never use benzine, thinners, alcohol or solvents of any kind,
to avoid the possibility of discoloration and/or deformation.
Additional Precautions
• Use a reasonable amount of care when using the unit’s
307
553
• Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions
and/or damage to speakers or other devices.
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
308
556
• Although the LEDs are switched off when the POWER
• When connecting / disconnecting all cables, grasp the
switch is switched off, this does not mean that the unit has
been completely disconnected from the source of power. If
you need to turn off the power completely, first turn off
the POWER switch, then unplug the power cord from the
power outlet. For this reason, the outlet into which you
choose to connect the power cord’s plug should be one
that is within easy reach.
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s
internal elements.
557
• A small amount of heat will radiate from the unit during
normal operation.
558a
• To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about
those around you (especially when it is late at night).
Placement
351
• Using the unit near power amplifiers (or other equipment
559a
containing large power transformers) may induce hum. To
alleviate the problem, change the orientation of this unit; or
move it farther away from the source of interference.
• When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise,
you will need to use equivalent packaging materials.
352a
921
•
This device may interfere with radio and television reception.
• To prevent malfunction and/or damage to speakers or
Do not use this device in the vicinity of such receivers.
other devices, always turn down the volume, and turn off
the power on all devices before making any connections.
352b
• Noise may be produced if wireless communications devices,
941
such as cell phones, are operated in the vicinity of this unit.
Such noise could occur when receiving or initiating a call, or
while conversing. Should you experience such problems,
you should relocate such wireless devices so they are at a
greater distance from this unit, or switch them off.
• Once the connections have been completed, turn on power
to your various devices in the order specified. By turning
on devices in the wrong order, you risk causing
malfunction and/or damage to speakers and other devices.
1. Turn on the device connected to the CUBE-60’s input
jack.
354b
• Do not expose the unit to direct sunlight, place it near
devices that radiate heat, leave it inside an enclosed
vehicle, or otherwise subject it to temperature extremes.
Also, do not allow lighting devices that normally are used
while their light source is very close to the unit (such as a
piano light), or powerful spotlights to shine upon the
same area of the unit for extended periods of time.
Excessive heat can deform or discolor the unit.
2. Turn on the CUBE-60.
3. Switch on any equipment connected to the CUBE-60’s
LINE OUT and RECORDING OUT/PHONES jacks.
Turn off the devices in the reverse order to which they
were switched on.
• Wrap the power cord around the cord hook when trans-
porting or storing the unit.
355b
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit. Damage
or malfunction may result if you attempt to use the unit in
this condition. Therefore, before using the unit, you must
allow it to stand for several hours, until the condensation
has completely evaporated.
• Do not insert hands, fingers, etc, into the openings in the
unit's rear panel. In particular, if the unit is to used in
households with small children, always provide adult
supervision to ensure that children keep their hands and
feet out of these openings.
356
• Do not allow rubber, vinyl, or similar materials to remain
on the unit for long periods of time. Such objects can
discolor or otherwise harmfully affect the finish.
359
• Do not paste stickers, decals, or the like to this instrument.
Peeling such matter off the instrument may damage the
exterior finish.
5
Panel Descriptions
Control Panel
fig.01
8
9
10
11
12
13
14
16
1
3
4
2
5
6
7
15
BLACK PANEL
1. INPUT Jack
This is modeled on the classic Fender Twin Reverb amplifier,
used in a wide variety of musical styles, from country to blues,
jazz and rock. Exhibiting rich lows and a bright high end.
Connect your guitar here.
2. SELECT Switch
BRIT COMBO
Switches you between the JC CLEAN and LEAD channels.
You can confirm which channel is selected by checking the
indicator’s color (JC CLEAN: green; LEAD: red).
The channel can be switched using the optional BOSS FS-5U
foot switch.
This is modeled on the Vox AC-30TB, the rock amplifier that
created the Liverpool sound of the ’60s. It can produce a
broad range of sounds, from clean to overdrive.
TWEED
This is modeled on the vintage Tweed Fender Bassman 4x10
Combo. The amplifier’s four 10-inch speakers produce a
clear upper-midrange with a fat low end, and its unique
crunch tones make it a favorite of blues-rock guitarists.
JC CLEAN Channel
This is a model of Roland’s famous JC-120 Jazz Chorus guitar
amplifier.
The ultra-clean, ultra-flat sound offers a smooth. This becomes
more effective when used in combination with a multi effector.
CLASSIC STACK
This is modeled on the sound and response of a Marshall
JMP1987. Used extensively in hard rock during the 1970s,
this is truly the perfect amp for the “top rock” guitar sound.
3. BRIGHT Switch
Creates a sparkling midrange and high end for a crisp and
distinct sound.
METAL STACK
This is modeled on the Peavey EVH-5150. This is the high
gain amp, so even at low volumes, you can still get heavy
distortion and sustain.
This is perfect for chord strumming with humbucking pickups.
4. VOLUME Knob
R-FIER STACK
Adjusts the JC CLEAN channel volume. On the CUBE-60,
distortion is gradually added as you turn this knob to the
right, producing a crunch sound as the knob is turned up
near maximum.
This is modeled on the MESA/Boogie Rectifier. This super
high gain amp is capable of producing slash metal, grunge,
and a wide range of other lead sounds.
DYNA AMP
This is an original amp sound that lets the player create
previously unobtainable tonal changes according to the
picking strength. Soft picking produces a transparent clean
amp sound, while hard picking results in a deeply distorted
high-gain amp sound. Once the sound is distorted, the tone
then changes according to the force used in picking, greatly
expanding your range of expression.
LEAD Channel
5. Type Switch
You can select from the following eight amp types:
ACOUSTIC
This is an original amp type included with the acoustic
simulator. Turns the sounds from your electric guitar into a
clear, refined acoustic guitar sound.
Setting the GAIN knob to the optimal position provides
the greatest effect.
Start by setting the GAIN knob to the center position,
then adjust the knob so that a clean tone is obtained
with soft picking and deep distortion is obtained with
hard picking.
Using this type together with a single coil pickup in the
front position provides optimum sound quality. If using
a humbucking pickup, slightly turn down the
equalizer’s BASS and MIDDLE settings.
“Sample Settings” (p. 10; Dynamic Style)
6
Panel Descriptions
fig.04PHASER
*
All product names mentioned in this document are trademarks or
registered trademarks of their respective owners, and are not
related to Roland Corporation.
In this manual, these names are used as appropriate ways to
indicate sounds that are simulated using COSM technology.
This effect adds a variable phase-
shifted signal to the direct sound,
giving the sound a swirling character.
fig.05TREMOLO
6. GAIN Knob
Adjusts the LEAD channel’s distortion level.
Tremolo is an effect that creates a
cyclic change in volume.
7. VOLUME Knob
Adjusts the LEAD channel volume.
EQUALIZER
DELAY/REVERB
8. BASS Knob
13. DELAY/REVERB Knob
Adjusts the tone of the lower range.
Turn this knob to DELAY or REVERB to switch to that effect.
Turn the knob to adjust the amount of effect applied.
The ON indicator lights up when DELAY or REVERB is
turned on, and goes out when DELAY or REVERB is turned
off. You can also turn DELAY or REVERB on and off using
an optional foot switch (the BOSS FS-5U).
9. MIDDLE Knob
Adjusts the tone of the midrange.
10.TREBLE Knob
Adjusts the tone of the upper range.
*
Graduations for DELAY, REVERB on a panel are for reference.
Be sure to check the sound as you adjust the effects.
*
No sound will be produced when BASS, MIDDLE, and TREBLE
knobs are all set to 0 while the Type switch is set to BLACK
PANEL or TWEED.
fig.05Da ELAY
Turn the knob to change the time and
amount of delay effects.
PRESENCE
11. PRESENCE Knob
fig.05Rb EVERB
Gives the midrange and high end a more lustrous contour.
Very effective when you want to give the sound a good
feeling of airiness.
Turn the knob to adjust the reverb level.
EFX (Effects)
14. RECORDING OUT/PHONES Jack
When Using RECORDING OUT
12. EFX (Effects) Knob
Turn this knob to chorus, flanger, phaser, or tremolo to
select the corresponding effect. Turn the knob to adjust the
amount of effect applied.
Connect to a recorder or other recording device.
Features COSM speaker modeling, allowing you to use the
CUBE-60 as a high-performance amp simulator.
When Using Headphones
The ON indicator lights up when EFX is turned on, and
goes out when EFX is turned off. You can also turn EFX on
and off using an optional foot switch (the BOSS FS-5U).
Connect headphones to this jack.
The COSM speaker modeling allows the guitar amp to
produce sounds with real punch.
*
Graduations for CHORUS, FLANGER, PHASER, TREMOLO
on a panel are for reference. Be sure to check the sound as you
adjust the effects.
*
No sound is output from the CUBE-60’s speaker or any external
speaker when the RECORDING OUT/PHONES jack is in use.
fig.02CHORUS
15. POWER Switch
In this effect, a slightly detuned sound
Turn the power on and off.
is added to the original sound, giving
the sound greater breadth and
fullness.
*
*
This unit is equipped with a protection circuit. A brief interval (a few
seconds) after power up is required before the unit will operate normally.
Always make sure to have the volume level turned down before
switching on power. Even with the volume all the way down, you
may still hear some sound when the power is switched on, but this
is normal, and does not indicate a malfunction.
fig.03FLANGER
This creates a flanging effect that
creates a sort of spinning sensation
with the sound.
16. Power Indicator
This indicator lights when the unit is turned on.
7
Panel Descriptions
Rear Panel
1
2
3
4
Speaker
cable
INPUT
Tuner
FS-5U
FS-5U
FS-5U
INPUT
INPUT
External Speaker
Mixer
*
*
Only use speaker cable to connect the speaker. Do not use any
shielded cable designed for use with guitars.
1. FOOT SW (Foot Switch) Jack
Foot switches (the optional BOSS FS-5U) are connected here.
No sound is output from the CUBE-60’s speaker or any external
speaker when the RECORDING OUT/PHONES jack is in use.
*
Set the polarity switch as shown below.
fig.06
3. LINE OUT Jack
Connects to a PA system, recorder, or other external system.
The COSM speaker modeling allows the guitar amp to
produce sounds with real punch.
Polarity switch
(CH SELECT)
Use this when using the unit with an external PA system or
when line-recording performances while listening to the
sound from the CUBE-60’s speaker.
Switches JC CLEAN/LEAD channels.
(EFX)
Adjust the output level with the JC CLEAN channel or
LEAD channel VOLUME knob.
Switches on and off of EFX.
(DELAY/REVERB)
Switches on and off of DELAY/REVERB.
4. TUNER OUT Jack
Connect tuner to this jack.
2. EXT SPEAKER (External Speaker) Jack
You can connect external speaker here.
*
The output from here is unaffected by the CUBE-60’s knob and
switch settings.
When connected, sounds are played from both the CUBE-60
and the external speakers.
................................................................................................................
Q: The volume level of the instrument connected to the CUBE-
60 is too low.
*
When connecting to an external speaker, make sure the speaker
conforms to the following specifications.
Impedance: 8 Ω maximum
A: Could you be using a connection cable that contains a resistor?
Use a connection cable that does not contain a resistor.
................................................................................................................
Allowable power input: 60 watts minimum
8
Sample Settings
Alternative Metal
The perfect sound for heavy, sharp riffs.
Select the high-gain R-FIER amp, then use the equalizer to
boost the low end even more.
You can add even more to the distortion’s edge by raising
the presence.
Used with a humbucking pickup in the rear position, it
results in an extreme distortion effect.
Plus, you can add a long delay to use this as a lead sound
with great sustain.
SELECT : LEAD
Space Clean
This is a transparent sound using spacial effects.
Select the JC CLEAN amp, modeled on the Roland JC-120,
then add chorus and long delay.
Using this setting with a guitar equipped with single coil
pickups makes beautiful sounding arpeggios and chord
strumming.
If using a humbucking pickup, turn the BRIGHT switch to
ON to achieve a bright, sparkling sound.
BRIGHT : ON or OFF SELECT : JC CLEAN
Depending on the phrase being played, it can be effective
to set the delay sound’s delay time slightly slower than the
phrase’s tempo.
Swamp Crunch
This is a blues sound found in vintage amps.
The boosted midrange is a particular characteristic of the
TWEED amp.
By adjusting the TREBLE knob, you can emphasize the
picking’s attack sound.
To create a fat, sweet sound, reduce the presence a little.
To produce a transparent and sharp crunch sound, lower
the midrange and boost the presence slightly.
SELECT : LEAD
You can also control the tube amp’s characteristic sustain
by adjusting the GAIN knob.
Classic Rock
This is a 70s-style rock sound.
Turning up the gain produces a powerful rock sound in all
riffs and solos.
A powerful low end is a characteristic of the sound emitted
by the surfaces of the cabinet, so you can turn up the
equalizer knobs, especially the BASS knob, and increase
the presence to produce a sound with great punch.
Turning the GAIN knob and equalizer all the way up
produces an even more powerful, driving sound.
SELECT : LEAD
Turning down the GAIN knob is also a perfect way to get a
sharp crunch sound.
9
Sample Settings
Dynamic Style
DYNA AMP is an original amp that uses relative picking
strength to create changes in distortion depth.
First, adjust the GAIN knob so that a clean tone is obtained
with soft picking and deep distortion is obtained when you
pick hard.
Now, mixing arpeggios played with a gentle touch along
with firmly picked chords and solos results in a guitar
sound with huge dynamics.
Now, to create a broader, more open sound, cut the
midrange and raise the low end and presence.
Using this in combination with the EFX and delay and
reverb creates a sound with an even greater feeling of scale.
SELECT : LEAD
Country Twang
A dry, distinctive country sound.
The BLACK PANEL amp has a powerful midrange
supported by a thick, solid low end, providing a clean
sound that is punchy and sweet.
By adjusting the sound while maintaining the balance
between the low and high ends, and in some cases cutting
back on the midrange, you bring out the guitar's bright
resonance even more.
Adding deep tremolo and reverb creates a good effect on
guitars equipped with single-coil pickups.
SELECT : LEAD
On guitars equipped with humbucking pickups, turning
down the highs creates a sweet sound that is perfectly
matched for jazz and similar genres.
Mersey Beat
This is the famous Liverpool sound from the past.
This sound features a mild distortion that still lets all the
notes in a chord come through clearly and distinctly.
Raise the midrange and presence on the BRIT COMBO
amp to create a lively, energetic sound.
Adjust the GAIN knob so that sound does not distort too
much when you play chords.
Use of a rear pickup provides a powerful sound with no
muddiness, producing a beautiful resonance when mixing
open strings with chords.
SELECT : LEAD
The sound may distort excessively when a guitar equipped
with humbucking pickups or other high-output guitar is
used. If this occurs, you can reduce the gain in order to get
a good balance between the guitar sound and the
distortion sound, or alternatively, you can adjust the sound
by cutting back the low end.
Setting Name:
Use this for keeping notes regarding your settings.
.....................................................................................................
.....................................................................................................
.....................................................................................................
.....................................................................................................
.....................................................................................................
.....................................................................................................
.....................................................................................................
.....................................................................................................
BRIGHT switch
SELECT switch
JC CLEAN
LEAD
ON
OFF
10
Main Specifications
Rated Power Output
60 W
Connectors
INPUT Jack (1/4” phone type)
RECORDING OUT/PHONES Jack (Stereo 1/4” phone type)
FOOT SW Jack (CH SELECT, EFX, DELAY/REVERB) (1/4”
phone type)
Nominal Input Level (1 kHz)
INPUT: -10 dBu/1 MΩ
EXT SPEAKER Jack (1/4” phone type)
LINE OUT Jack (1/4” phone type)
TUNER OUT Jack (1/4” phone type)
Speaker
30 cm (12 inches)
Controls
Power Supply
AC 117 V, AC 230 V, AC 240 V (50/60 Hz)
AC 220 V (60 Hz)
POWER Switch, SELECT Switch
<JC CLEAN Channel>
BRIGHT Switch, VOLUME Knob
Power Consumption
<LEAD Channel>
60 W
TYPE Switch (ACOUSTIC, BLACK PANEL, BRIT COMBO,
TWEED, CLASSIC STACK, METAL STACK, R-FIER STACK,
DYNA AMP), GAIN Knob, VOLUME Knob
Dimensions
410 (W) x 275 (D) x 440 (H) mm
16-3/16 (W) x 10-7/8 (D) x 17-3/8 (H) inches
<EQUALIZER>
BASS Knob, MIDDLE Knob, TREBLE Knob
Weight
14.5 kg / 32 lbs
<PRESENCE>
PRESENCE Knob
<EFX>
Accessory
Owner’s Manual
EFX Knob (CHORUS, FLANGER, PHASER, TREMOLO)
<DELAY/REVERB>
Option
DELAY/REVERB Knob
Foot Switch FS-5U (BOSS)
Indicators
JC CLEAN Channel, LEAD Channel, EFX, DELAY/REVERB,
POWER
*
*
0 dBu = 0.775 Vrms
In the interest of product improvement, the specifications and/or
appearance of this unit are subject to change without prior notice.
Block Diagram
INPUT
SELECT
SPEAKER
POWER AMP
JC CLEAN
LEAD
DELAY/
REVERB
EFX
EXT SPEAKER
LINE OUT
ACOUSTIC
BLACK PANEL
BRIT COMBO
TWEED
CABINET &
SPEAKER
SIMULATOR
CLASSIC STACK
METAL STACK
R-FIER STACK
DYNA AMP
RECORDING OUT/
PHONES
* No sound is played through the unit’s speaker and
external speaker while the PHONES jack is in use.
TUNER OUT
11
Information
When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as
shown below.
MEXICO
IRELAND
PHILIPPINES
IRAN
AFRICA
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico D.F.
MEXICO
Roland Ireland
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
MOCO, INC.
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
EGYPT
Al Fanny Trading Office
9, EBN Hagar A1 Askalany Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: (55) 5668-6699
TEL: (02) 899 9801
TEL: (021) 285-4169
PANAMA
SINGAPORE
ISRAEL
ITALY
TEL: 20-2-417-1828
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City, REP. DE PANAMA
TEL: 315-0101
Swee Lee Company
150 Sims Drive,
Halilit P. Greenspoon &
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
Sons Ltd.
REUNION
SINGAPORE 387381
TEL: 6846-3676
8 Retzif Ha'aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
CRISTOFORI MUSIC PTE
PARAGUAY
NORWAY
LTD
Distribuidora De
JORDAN
Roland Scandinavia Avd.
Blk 3014, Bedok Industrial Park E,
#02-2148, SINGAPORE 489980
TEL: 6243-9555
REUNION ISLAND
TEL: (0262) 218-429
Instrumentos Musicales
J.E. Olear y ESQ. Manduvira
Asuncion PARAGUAY
TEL: (021) 492-124
AMMAN Trading Agency
245 Prince Mohammad St.,
Amman 1118, JORDAN
TEL: (06) 464-1200
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
SOUTH AFRICA
TAIWAN
That Other Music Shop
TEL: 2273 0074
ROLAND TAIWAN
(PTY) Ltd.
11 Melle St., Braamfontein,
Johannesbourg, SOUTH AFRICA
KUWAIT
URUGUAY
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung Shan
N.Road Sec.2, Taipei, TAIWAN,
R.O.C.
Easa Husain Al Yousifi Est.
Abdullah Salem Street,
Safat, KUWAIT
POLAND
Todo Musica S.A.
Francisco Acuna de Figueroa 1771
C.P.: 11.800
MX MUSIC SP.Z.O.O.
UL. Gibraltarska 4.
P.O.Box 32918, Braamfontein 2017
Johannesbourg, SOUTH AFRICA
TEL: (011) 403 4105
TEL: 243-6399
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
Montevideo, URUGUAY
TEL: (02) 924-2335
TEL: (02) 2561 3339
LEBANON
THAILAND
Paul Bothner (PTY) Ltd.
17 Werdmuller Centre,
Main Road, Claremont 7708
SOUTH AFRICA
Chahine S.A.L.
PORTUGAL
VENEZUELA
Theera Music Co. , Ltd.
330 Verng NakornKasem, Soi 2,
Bangkok 10100, THAILAND
TEL: (02) 2248821
Gerge Zeidan St., Chahine Bldg.,
Achrafieh, P.O.Box: 16-5857
Beirut, LEBANON
Tecnologias Musica e Audio,
Roland Portugal, S.A.
Cais Das Pedras, 8/9-1 Dto
4050-465 PORTO
Musicland Digital C.A.
Av. Francisco de Miranda,
Centro Parque de Cristal, Nivel
C2 Local 20 Caracas
TEL: (01) 20-1441
P.O.BOX 23032, Claremont 7735,
SOUTH AFRICA
TEL: (021) 674 4030
PORTUGAL
TEL: (022) 608 00 60
VIETNAM
VENEZUELA
TEL: (212) 285-8586
QATAR
Saigon Music
Al Emadi Co. (Badie Studio
& Stores)
Suite DP-8
ROMANIA
40 Ba Huyen Thanh Quan Street
Hochiminh City, VIETNAM
Tel: (08) 930-1969
P.O. Box 62, Doha, QATAR
TEL: 4423-554
ASIA
FBS LINES
EUROPE
Piata Libertatii 1,
535500 Gheorgheni, ROMANIA
TEL: (266) 364 609
CHINA
SAUDI ARABIA
AUSTRIA
Roland Shanghai Electronics
aDawliah Universal
AUSTRALIA/
NEW ZEALAND
Roland Austria GES.M.B.H.
Siemensstrasse 4, P.O. Box 74,
A-6063 RUM, AUSTRIA
Co.,Ltd.
RUSSIA
Electronics APL
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
MuTek
Corniche Road, Aldossary Bldg.,
1st Floor, Alkhobar,
SAUDI ARABIA
3-Bogatyrskaya Str. 1.k.l
107 564 Moscow, RUSSIA
TEL: (095) 169 5043
TEL: (0512) 26 44 260
AUSTRALIA
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 Anhuaxili
Chaoyang District, Beijing 100011
CHINA
Roland Corporation
Australia Pty., Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
BELGIUM/HOLLAND/
LUXEMBOURG
Roland Benelux N. V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
SPAIN
Roland Electronics
de España, S. A.
Calle Bolivia 239, 08020
Barcelona, SPAIN
TEL: (93) 308 1000
SYRIA
TEL: (02) 9982 8266
Technical Light & Sound
TEL: (010) 6426-5050
Center
NEW ZEALAND
CZECH REP.
K-AUDIO
Kardasovska 626.
CZ-198 00 Praha 9,
CZECH REP.
Roland Shanghai Electronics
Co.,Ltd.
(GUANGZHOU OFFICE)
2/F., No.30 Si You Nan Er Jie Yi
Xiang, Wu Yang Xin Cheng,
Guangzhou 510600, CHINA
Tel: (020) 8736-0428
Khaled Ebn Al Walid St.
Bldg. No. 47, P.O.BOX 13520,
Damascus, SYRIA
TEL: (011) 223-5384
Roland Corporation Ltd.
32 Shaddock Street, Mount Eden,
Auckland, NEW ZEALAND
TEL: (09) 3098 715
SWEDEN
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
TEL: (2) 666 10529
TURKEY
CENTRAL/LATIN
AMERICA
Ant Muzik Aletleri Ithalat
DENMARK
Ve Ihracat Ltd Sti
Siraselviler Caddesi Siraselviler
Pasaji No:74/20
Taksim - Istanbul, TURKEY
TEL: (0212) 2499324
HONG KONG
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
SWITZERLAND
Tom Lee Music Co., Ltd.
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
Service Division
22-32 Pun Shan Street, Tsuen
Wan, New Territories,
HONG KONG
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
TEL: 3916 6200
SWITZERLAND
TEL: (061) 927-8383
U.A.E.
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
TEL: 2415 0911
FRANCE
Zak Electronics & Musical
Roland France SA
UKRAINE
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai, U.A.E.
TEL: (04) 3360715
Parsons Music Ltd.
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
4, Rue Paul Henri SPAAK,
Parc de l'Esplanade, F 77 462 St.
Thibault, Lagny Cedex FRANCE
TEL: 01 600 73 500
TIC-TAC
BRAZIL
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo, UKRAINE
TEL: (03131) 414-40
Roland Brasil Ltda
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
FINLAND
INDIA
NORTH AMERICA
Roland Scandinavia As,
Filial Finland
UNITED KINGDOM
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra Mahalaxmi
Flats Compound Off. Dr. Edwin
Moses Road, Mumbai-400011,
INDIA
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
Elannontie 5
CANADA
COSTA RICA
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
Roland Canada Music Ltd.
JUAN Bansbach
(Head Office)
Instrumentos Musicales
Ave.1. Calle 11, Apartado 10237,
San Jose, COSTA RICA
TEL: 258-0211
UNITED KINGDOM
TEL: (01792) 702701
TEL: (022) 2493 9051
5480 Parkwood Way Richmond
B. C., V6V 2M4 CANADA
TEL: (604) 270 6626
GERMANY
Roland Elektronische
INDONESIA
Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt,
GERMANY
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
Roland Canada Music Ltd.
CHILE
MIDDLE EAST
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
Comercial Fancy S.A.
Rut.: 96.919.420-1
TEL: (040) 52 60090
INDONESIA
TEL: (021) 6324170
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
BAHRAIN
GREECE
Moon Stores
KOREA
TEL: (905) 362 9707
STOLLAS S.A.
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
U. S. A.
EL SALVADOR
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: 211 005
OMNI MUSIC
75 Avenida Norte y Final
CYPRUS
Alameda Juan Pablo
Edificio No.4010 San Salvador,
EL SALVADOR
,
MALAYSIA
HUNGARY
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia,
CYPRUS
TEL: (323) 890 3700
BENTLEY MUSIC SDN BHD
140 & 142, Jalan Bukit Bintang
55100 Kuala Lumpur,MALAYSIA
TEL: (03) 2144-3333
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint, HUNGARY
TEL: (23) 511011
TEL: 262-0788
TEL: (022) 66-9426
As of November 1, 2003 (Roland)
SD000453
1GT
|