RF-TVMFM03_10-0726_QSG_V2_EN.eps 1 7/2/2010 1:18:59 PM
V2
FINAL
FOR PRINT
QUICK SETUP GUIDE
1 Install the TV brackets
2 Add the horizontal bars
RF-TVMFM03
Option 1: Installing for a flat mounting surface
1 Slide the horizontal bars (C) through the wire guides on the TV brackets.
2 Secure the bars to the TV brackets using the 9/16 in. × 8/32 in. Phillips head screws (W).
1 Align the TV brackets (A and B) with the screw holes on the back of the TV.
2 Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV brackets that
align with the screw holes on the back of the TV, then insert the M4 screws (F), M5 screws (J),
M6 screws (L or M), or M8 screws (Q) through the washers.
Note: Intended for use on
wood stud walls with 16 in.
or less spacing only.
3 Tighten the screws until they are snug against the TV bracket. Do not over tighten.
Thank you for choosing the Rocketfish RF-TVMFM03.
The RF-TVMFM03 TV mount is designed to support a
flat-panel TV weighing up to 130 lbs. (58.9 kg).
R
or
Package contents
A Right vertical TV bracket (1)
M8 bag
Q M8 × 16 mm screws (4)
B Left vertical TV bracket (1)
C
Horizontal TV bracket (2)
D Arm assembly (1)
Wall plate (1)
M4 bag
R
S
M8 × 40 mm screws (4)
M8 × 60 mm screws (4)
or
E
Hex key bag
T
3/16 in. hex key (1)
C
M
3 Install the wall plate to a wood stud wall
Note: Any material covering the wall must not exceed 5/8 in. (16 mm).
1 Locate the studs. Verify the center of the stud with an awl
or thin nail or use an edge-to-edge stud finder.
F
M4 × 12 mm screws (4)
Lag bolt bag
G M4 × 30 mm screws (4)
U Lag bolt washer (4)
V 5/16 in. × 2-3/4 in. lag bolt (4)
Bracket hardware
W 9/16 in. × 8/32 in. Phillips head screw (4)
X 3/8 in. × 8/32 in. Phillips head screw (1)
Cable ties
Y
H M4/M5 washers (8)
CM
MY
CY
CMY
K
Option 2: Installing for an obstructed mounting surface
Note: Use additional washers (H) with M4/M5 hardware only.
I
M4/M5 spacers (4)
<5/8 in.
2 Level the wall plate (E) and mark the hole locations.
M5 bag
16 in.
1 Place the M4/M5 spacers (I) or M6/M8 spacers (P) and the M4/M5 washers (H) into the
recessed screw holes on the back of the TV.
2 Align the TV brackets (A and B) with the spacers and washers on the back of the TV.
3 Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV brackets that
align with the screw holes on the back of the TV, then insert the M4 screws (G), M5 screws (K),
M6 screws (N), or M8 screws (R or S) through the washers.
J
M5 × 12 mm screws (4)
3 Drill pilot hole to a depth of 3 in. using a 7/32 in. diameter drill bit.
4 Align the wall plate (E) with the pilot holes.
5 Place the washers (U) over the holes in the wall plate (E),
insert the lag bolts (V) through the washers, then tighten
the lag bolts only until the washers (U) are pulled firmly
against the wall plate.
K M5 × 30 mm screws (4)
M6 bag
Y 8 in. nylon cable ties (5)
Cap screws
L
M6 × 12 mm screws (4)
M M6 × 20 mm screws (4)
N M6 × 35 mm screws (4)
O M6/M8 washers (4)
Z
5/32 in. hex key (1)
AA Cap screws (2)
4 Tighten the screws until they are snug against the TV bracket. Do not over tighten.
P
M6/M8 spacers (4)
A
B
C
CAUTION: Avoid potential
injuries or property damage!
DO NOT over-tighten
the lag bolts (V).
M4 bag
F
G
M4 × 12 mm
M4 × 30 mm
H
I
M4/M5
M4/M5
M5 bag
E
J
K
D
M5 × 30 mm
M5 × 12 mm
M6 bag
P
L
M
N
O
M6/M8
M6 × 12 mm
M6 × 20 mm
M6 × 35 mm
M6/M8
Bracket hardware
Wall
M8 bag
Q
R
S
W
X
10-1/5 in.
7 in.
(75 mm)
3 in.
M8 × 16 mm
M8 × 40 mm
M8 × 60 mm
TV
Hex key bag
Cable ties
Y
T
TV shifts 7 in. from the home position to
full extension.
3/16 in.
Cap screws with hex key
or
U
V
Z
Lag bolt bag
5/32 in.
AA
5/16 in. × 2-3/4 in.
or
Tools you will need:
•
•
•
•
•
•
Stud finder
Awl
•
Socket wrench with
1/2 in. socket or
adjustable wrench
7/32 in. wood drill bit
Power drill
Pencil
Level
Tape measure
Phillips screwdriver
or
•
•
|